I have covered many different types of ceiling devotee installations in prior website posts and in video, but this post will center on taking an present ceiling fan that is currently harnessed by deuce paries switches, and converting it to a remote controlled ceiling devotee c/w loose kit.
We will be exploitation a comprehensive remote control unit of measurement from Hampton Bay, Model #27157.
SAFETY FIRST!
The first step (arsenic forever) is to square up what circuit breaker feeds power to the circuit we are working on, and shut off that breaker. For a quick review of safety considerations when working around electricity, Flick HERE.
Now that the breaker is polish off, and the electrical board is locked (if so appointed) thus nobody commode accidentally turning the breaker back connected while you are running on the circuit you can safely set out working.
If you don't have victuals for locking off the access to the panel, put a piece of electrical videotape over the breaker handgrip holding it in the off position, and post a note warning others to go out the surf off.
Bump off THE FAN CANOPY COVER
The next step is to remove the canopy of the lover to check happening the present wiring, and plan for the installation of the remote receiver unit. With this particular fan, a prune ring conceals the four mounting screws that hold the canopy cover in situ. Turn the hoop a ¼ turn until it comes loose and then remove the four screws. You only need to totally remove one of the screws on each side, and just loosen the otherwise two that are through the primal-hole, or L-slots in the canopy cover to allow it to drop taboo of the means, exposing the mounting bracket and the fan wiring.
Disconnection THE Present WIRING
Determine how the fan is connected now. There is a 3-wire cable in the outlet box that provides a common neutral (white) wire, and the fan's light kit is connected to the red, and the fan is related to the pitch-dark conductor. We only need one of these switched baking wires to act the master ability for the receiver unit. I bequeath usance the black wire (and the neutral conductor) to power the receiver, and the new wire (red) will beryllium capped off with a wire nut and will no thirster be used in this installation. Here's a plot showing how the fan was connected to the switches at the start.
Ceiling Sports fan Unaccessible Conversion Original Connections
Copulative THE REMOTE RECEIVER
Now we disconnect the fan and inflamed kit out and fix to install the remote pass catcher.
The white wire from the add cable television wish relate to the line in neutral, and the black wire will connect to the vital in, OR power in wire from the receiver. The neutral out from the pass receiver will now connect to the common neutral for the buff / light up, and the sarcastic lover cable will go to the wire labelled "sports fan" (red), and the blue light kit wire will connect to the telegraph labelled for the brightness level.
Here's a plot showing how the connections are made to the far receiver.
With all the connections made, we need to tuck the wires second into the box and install the remote receiver in the space getable in the climb bracket. This can be a difficult job to make everything match, but it's important that everything fits in nicely and that No wires are pinched or packed in too tightly so to avoid any damage to the conductors, potentially causation a short-snouted circuit condition.
When the remote receiver is installed and the canopy and tailored ring are back in place, we can now produce our changes in the multi-crowd flip-flop box.
In this instalmen, the two switches that controlled the fan/light are in a 3-gang box that also has the transposition for the switched receptacles in the room. Remove the faceplate and the device screws and regulate that the switch that controlled the sunlit has a red wire on one terminal, and the switch over that controlled the fan has a total darkness telegraph on one incline of it. Both switches wish suffer a black hot wire from the same hot splice connected to to each one switch. We want to remove the flip-flop we no longer call for, and cap bump off the wires with wire nuts. We are abandoning the redness cable here as we did in the fan wall socket. We will use the remaining switch as a master control for the remote pass catcher. I will make a motion the switch we are still using to the middle position, keep open the swop for the room's receptacles in the first position, and then use a blank filler plateful to fill the position of the switch we removed.
With the switches back in put on, and the faceplate installed, it's time to check our installation.
Restore power to the racing circuit and then turn on the master key switch on the fence in. The remote should now ascertain the operation of the fan and the ignitor. The fan amphetamine and direction testament have to be set to the desired position using the pull-Chain and annul switch, and the light kit pull-range will have to be happening as well in rank for the remote to make for.
Changing a ceiling fan to outback control is an excellent resolution for many applications, but especially in a bedchamber where the switch is by the entrance room access. You can buoy keep the remote on the bedside table, and have get at to the light and the devotee if needed in the middle of the Nox, without getting out of bed!
If you aren't well-heeled and confident in safely completing a project like this on your own, use the box on the left of the pageboy to find a reliable trusted licensed electrician in your local area.
Away Terry cloth Peterman, The Cyberspace Electrician®
Can I Add a Remote Control to My Ceiling Fan
Source: https://www.electrical-online.com/converting-an-existing-ceiling-fan-to-a-remote-control/
Postar um comentário